Serving the Albuquerque area  ·  (505) 420-5488  ·  Open Mon-Sun 7am-7pm
📞 (505) 420-5488 Free Quote

Metal Roofing in Moriarty, NM (87035) · Local Professionals

Albuquerque Metal Roofing · Fast response in Moriarty and the Albuquerque area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+196Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Moriarty sits out east of the mountains where the wind never really stops and the lots are big enough for a barn, a shop, and a horse or two. If you live off Route 66 or down a gravel road near the Moriarty Municipal Schools campus, you already know that hail, spring gusts, and winter freeze-thaw tear up roofs faster than anything in town.

We are Albuquerque Metal Roofing, and we work Moriarty and ZIP 87035 because we know what ranch country does to a roof. From the older homes near the Moriarty Community Center to the newer places off I-40, we handle metal roof installation, repair, and replacement with crews that are fully insured and used to working around livestock, equipment, and wide-open exposure.

Metal Roofing in Moriarty (87035)

Moriarty is high desert ranch country, and the ground here is caliche and gravel with very little to slow down water. That means drainage matters as much as the panels themselves. Properties out here often have long, low-slope shop roofs, barns with exposed-fastener R-panel, and homes with a mix of shingle and metal. The wind that comes across the Estancia Valley lifts ridge caps, works screws loose, and peels back panel edges if the fasteners and sealants were not spec'd for this exposure. Hail in the summer monsoon pounds the same roofs that bake under intense UV all year, so we see a lot of failed washers, chalky coatings, and flashing gaps at chimneys and skylights. Access can be tight on older ranch lots with gates, corrals, and equipment, and we plan for that before we ever set a ladder.

Our team has worked metal roofs across the East Mountains and the Albuquerque area for years, from standing seam and stone-coated steel to corrugated panels on outbuildings. We know how to match a profile to the property, whether it is a home near Moriarty High School or a commercial shop off the frontage road.

Our services in Moriarty

How a Job Works in Moriarty

Step 1: You call (505) 420-5488 or request a free estimate online. We schedule an on-site assessment, walk the roof and the perimeter, check fasteners, seams, flashing, and drainage, and talk through what you are seeing. For storm or wind damage, the inspection is free and we document what we find.

Step 2: We put together a written scope with materials, timeline, and pricing. In Moriarty, that often means coordinating around gates, animals, and gravel drives, and confirming permit requirements with the local building department before any tear-off or re-roof starts. If your property is in an HOA or a historic area, we help you get the profile and color approved before we order panels.

Step 3: The crew protects landscaping and equipment, tears off or retrofits as planned, and installs to manufacturer specs. When we are done, we magnet-sweep for screws and nails, haul away debris, and walk the finished roof with you so you know exactly what was done and what to watch for.

Pricing in Moriarty depends on square footage, roof pitch and complexity, access, and whether we are repairing or replacing. As a ballpark, metal roof installation starts around $8 per square foot, standing seam around $10, metal roof replacement around $9, and a retrofit over existing shingles around $7. Corrugated and ribbed panel roofing starts near $5.50 per square foot, while stone-coated steel and metal shingles start around $9. Repairs and leak fixes start at $450, screw replacement and re-fastening at $750, and flashing, chimney, or skylight work at $600. Coating and painting starts at $2.50 per square foot, and gutters for metal roofs start at $9 per linear foot. Storm and wind damage inspections are free. Call (505) 420-5488 for a free estimate tailored to your property.

My barn off the Moriarty frontage road has R-panel that keeps backing out screws. Can you fix that without replacing the whole roof?
Yes. Exposed-fastener panels on outbuildings commonly lose screws to wind vibration and freeze-thaw. We inspect the panel, replace failed screws with the correct washered fasteners, re-seat lifted edges, and check the ridge and eave trim. If the panels are still sound, re-fastening is usually the right fix and starts around $750.
A spring windstorm peeled back part of my roof near the Estancia Valley. How fast can you get out for storm damage?
We prioritize active leaks and wind damage in Moriarty and ZIP 87035. Call (505) 420-5488, and we will schedule a free inspection, document the damage for your records, and make temporary repairs if needed before the permanent fix.
What does a metal roof replacement cost for a typical ranch home in Moriarty?
Most ranch homes here land between $9 and $10 per square foot for replacement or standing seam, depending on roof size, pitch, access, and whether we tear off existing shingles. A simple retrofit over shingles can start around $7 per square foot. We give you a written number after the free on-site assessment.
Do I need a permit to re-roof my house in Moriarty, and who handles it?
Roofing permits are commonly required for a full replacement or re-roof, and requirements vary by jurisdiction. We confirm the rules with the local building department before work starts and can walk you through what is needed. We never guess on permits, and we defer to the building department for the final word.
My neighbor and I share a fence line and my new metal roof will be visible from their property. What about HOA or property line issues?
If you are in an HOA, we help you get the panel profile and color approved before ordering. For property lines, roof overhang and drainage should stay on your side, and we can set gutters and downspouts to direct water away from the line. If there is any question, we recommend confirming with your neighbor and the HOA in writing before installation.
Are you fully insured for work on my Moriarty property?
Yes. Albuquerque Metal Roofing carries general liability and workers' compensation insurance. We are happy to provide proof of coverage before we start, so you are protected if anything happens on your property.
What maintenance should I do on a metal roof in Moriarty to get ahead of winter?
Check fasteners and sealant at flashing and penetrations before the freeze-thaw cycles hit, clear debris from valleys and gutters, and look for lifted ridge caps after wind events. A fall inspection is the best way to catch small issues before snow and ice make them bigger. We offer free estimates for inspections and can set up a maintenance plan.
Why choose us?

Trusted professionals in Albuquerque

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Albuquerque

All your work handled by qualified professionals in Albuquerque

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

196+ Verified Client Reviews in Albuquerque

⭐⭐⭐⭐⭐ 4.9/5 · 196 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Albuquerque · Response within 24h · No commitment · ☎ (505) 420-5488

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Albuquerque ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm